Texas Arc Flash StudyGet a quote

NFPA 70E · OSHA · Texas

Arc Flash Study in Texas – Get a Quote

Request a quote for an arc flash study or arc flash risk assessment for your plant, warehouse, data center or commercial facility anywhere in Texas.

Your request goes to a partner firm of licensed Professional Engineers (PE) who scope the work and send you a proposal. No obligation.

Request a free quote

Takes about 60 seconds. No obligation.

By submitting, you agree to our Terms of use.

This site is a quote-request service. We connect Texas businesses with a partner firm of licensed Professional Engineers (PE). We are not a licensed engineering firm, do not perform engineering work, sign or seal studies, or provide engineering advice. All engineering is contracted directly with the licensed firm.

What's included in an arc flash study

Short-circuit study

Available fault current calculated at each bus, from the utility source down to panels and MCCs.

Protective device coordination

Breaker, fuse and relay curves reviewed so faults clear quickly and selectively.

Incident energy analysis

Incident energy (cal/cm²) and arc flash boundaries calculated per equipment location.

Arc flash labels

Durable labels with the information NFPA 70E requires, applied to assessed equipment.

One-line diagram updates

Single-line diagrams created or corrected to reflect the system as installed.

Why Texas facilities need an arc flash study

An arc flash is a release of energy caused by an electrical fault through air. It can produce intense heat, pressure, molten metal and light in a fraction of a second, and it is one of the most serious hazards electrical workers face. An arc flash study quantifies that hazard at each piece of equipment so that your workers and contractors know the risk and wear the right protection before they open a panel, rack a breaker or troubleshoot energized equipment.

NFPA 70E, the Standard for Electrical Safety in the Workplace, requires an arc flash risk assessment before anyone works within the arc flash boundary of energized equipment. OSHA does not adopt NFPA 70E word-for-word, but its general industry electrical standards in 29 CFR 1910 Subpart S and the General Duty Clause require employers to protect workers from recognized electrical hazards — and OSHA routinely points to NFPA 70E as the recognized consensus standard for doing so. Read our plain-English NFPA 70E and OSHA guide for more detail.

Who needs an arc flash study

  • Manufacturing plants with MCCs, switchgear and production equipment maintained in-house.
  • Oil & gas and chemical facilities, from Permian Basin compressor stations to Gulf Coast refineries.
  • Warehouses and distribution centers with conveyors, sortation and battery charging.
  • Data centers and hospitals with UPS, generators and transfer switches that must be modeled in several operating modes.
  • Commercial buildings with large services and in-house or contracted electrical maintenance.
  • Electrical contractors who need a study for a client or for a new installation they are commissioning.

The 5-year rule and major modifications

A study is not a one-time document. NFPA 70E requires the arc flash risk assessment to be reviewed for accuracy at intervals not to exceed five years, and to be updated when a major modification or renovation takes place. Electrical systems change: utilities upgrade transformers, facilities add generators, production lines are added and breakers are replaced. Any of these can raise or lower incident energy, which means old labels may understate the hazard. If your labels are more than five years old, or you've made significant electrical changes since your last study, select “Arc flash update” in the form.

How the arc flash study process typically works

1. Scoping and quote

You submit a short request. The partner PE firm reviews it, may ask a few questions about equipment counts and existing documentation, and sends you a proposal.

2. Field data collection

Engineers or technicians visit your facility to document transformers, conductors, protective devices and settings. Having an existing one-line diagram can reduce field time, but it is not required.

3. Modeling and analysis

The system is modeled in engineering software to perform the short-circuit, coordination and incident energy calculations, commonly based on the IEEE 1584 method.

4. Report, labels and recommendations

You receive a report, updated one-line diagrams and arc flash labels, plus recommendations such as setting changes that can reduce incident energy. See our arc flash label guide for what labels must include.

What it costs

Every facility is different, but as an indicative guide small facilities often fall around $3,500–$6,000 and mid-size facilities around $6,000–$14,000, while larger sites are custom-quoted. Our arc flash study cost guide explains the factors that drive price.

Also available: SPCC plans

Facilities that store oil above EPA thresholds — generally more than 1,320 gallons of aggregate aboveground capacity — may need a PE-certified Spill Prevention, Control and Countermeasure plan. Learn about SPCC plans and request a quote.

Serving facilities across Texas

Requests are accepted statewide, with dedicated information for:

An honest note about this site

Texas Arc Flash Study is a quote-request service. We connect Texas businesses with a partner firm of licensed Professional Engineers. We do not perform engineering work, and we do not sign or seal studies. The engineering firm you're connected with is responsible for its services, proposal and deliverables.

Frequently asked questions

What is an arc flash study?+

An arc flash study is an engineering analysis of a facility's electrical system that calculates the incident energy and arc flash boundary at each piece of equipment, so workers know the hazard and the PPE required. It typically includes a short-circuit study, protective device coordination study, incident energy analysis and arc flash labels.

How often is an arc flash study required?+

NFPA 70E requires the arc flash risk assessment to be reviewed for accuracy at intervals not to exceed five years, and to be updated when a major modification or renovation takes place.

Does Texas Arc Flash Study perform the engineering?+

No. We are a quote-request service. We forward your request to a partner firm of licensed Professional Engineers, which performs the work and contracts directly with you.

How much does an arc flash study cost in Texas?+

As an indicative guide, small facilities often fall around $3,500–$6,000 and mid-size facilities around $6,000–$14,000, while larger or complex sites are quoted individually. Actual pricing comes from the engineering firm's proposal.

Who should request a quote?+

Facility managers, plant managers, EHS and safety managers, maintenance leaders and electrical contractors responsible for commercial or industrial facilities in Texas.

Request a free quote

Takes about 60 seconds. No obligation.

By submitting, you agree to our Terms of use.

This site is a quote-request service. We connect Texas businesses with a partner firm of licensed Professional Engineers (PE). We are not a licensed engineering firm, do not perform engineering work, sign or seal studies, or provide engineering advice. All engineering is contracted directly with the licensed firm.