Texas Arc Flash StudyGet a quote

Compliance guide

NFPA 70E & OSHA Arc Flash Compliance

What NFPA 70E and OSHA actually expect from employers when it comes to arc flash hazards — explained without the legalese.

This page is general information, not legal or engineering advice. Requirements depend on your facility and the edition of the standard you follow; consult a licensed Professional Engineer and your safety advisors.

What is NFPA 70E?

NFPA 70E, the Standard for Electrical Safety in the Workplace, is published by the National Fire Protection Association and updated on a three-year cycle. It describes how employers and employees should work safely around electrical hazards — shock, arc flash and arc blast. Where the National Electrical Code (NFPA 70) covers how electrical systems are installed, NFPA 70E covers how people work on and near them.

The core ideas of NFPA 70E include:

  • Establish an electrically safe work condition (de-energize, lock out, test) as the primary protective strategy.
  • Justify energized work — only when de-energizing creates greater hazards or is infeasible, and usually with an energized electrical work permit.
  • Perform risk assessments for both shock and arc flash before work begins.
  • Maintain an electrical safety program with procedures, training, auditing and a hierarchy of risk controls.
  • Label equipment likely to require examination, adjustment, servicing or maintenance while energized.

The arc flash risk assessment

NFPA 70E requires an arc flash risk assessment to determine whether an arc flash hazard exists and, if so, the appropriate safety-related work practices, the arc flash boundary and the PPE to use within it. Employers can use one of two methods to select PPE:

Incident energy analysis method

The incident energy at a working distance is calculated for each piece of equipment using engineering data — typically through an arc flash study based on IEEE 1584. PPE is selected to have an arc rating at least equal to the calculated incident energy. This is the most precise method and the one most industrial facilities rely on.

Arc flash PPE category method

NFPA 70E tables assign a PPE category to common tasks on common equipment, but only when the equipment falls within the tables' stated limits for fault current and clearing time. Verifying those limits still requires knowing your available fault current and protective device performance — which is why many employers end up needing a study anyway.

Review every five years — and after major changes

The arc flash risk assessment must be reviewed for accuracy at intervals not to exceed five years and updated when a major modification or renovation occurs. It should also reflect the condition of maintenance of equipment, since poorly maintained breakers may not clear faults as quickly as their curves suggest.

Where OSHA comes in

OSHA is the federal agency that enforces workplace safety. It has not incorporated NFPA 70E by reference, but several OSHA requirements apply directly to arc flash hazards:

  • 29 CFR 1910 Subpart S (1910.301–1910.399) — electrical safety requirements for general industry, including safety-related work practices in 1910.331–1910.335.
  • 29 CFR 1910.132 — requires a workplace hazard assessment and appropriate PPE.
  • 29 CFR 1910.335 — requires protective equipment for employees working where there are potential electrical hazards.
  • 29 CFR 1910.269 — for electric power generation, transmission and distribution work, including explicit requirements to estimate incident heat energy.
  • The General Duty Clause, Section 5(a)(1) of the OSH Act — requires employers to keep the workplace free from recognized hazards likely to cause death or serious harm.

In practice, OSHA often cites NFPA 70E as evidence of how a recognized hazard can be abated. Following NFPA 70E, including performing and maintaining an arc flash risk assessment, is widely considered the accepted way to meet OSHA's expectations regarding arc flash.

Practical steps for Texas employers

  • Inventory equipment that may be worked on while energized.
  • Check the date and scope of your existing arc flash study and labels.
  • Confirm whether major electrical changes have occurred since the last study.
  • Update or create your written electrical safety program.
  • Train qualified workers on the program and on reading arc flash labels.
  • Request an arc flash study or update from licensed engineers.

Next, read about arc flash label requirements or check indicative study costs.

Frequently asked questions

Is NFPA 70E a law?+

NFPA 70E is a consensus standard, not a federal regulation. However, OSHA requires employers to protect workers from electrical hazards and regularly references NFPA 70E as the recognized way to meet those obligations.

Does OSHA require an arc flash study?+

OSHA's standards don't use the words “arc flash study,” but 29 CFR 1910 Subpart S, 1910.132 on PPE hazard assessment and the General Duty Clause require employers to assess hazards and provide protection. An arc flash risk assessment is the common way to do that for electrical work.

How often must the arc flash risk assessment be reviewed?+

NFPA 70E requires review for accuracy at intervals not exceeding five years, and updates when major modifications or renovations occur.

What is the difference between the incident energy method and the PPE category method?+

The incident energy analysis method calculates the specific energy at each location. The PPE category (table) method uses NFPA 70E tables under defined conditions. A study supports the incident energy method and makes labeling more precise.

Who is a qualified person under NFPA 70E?+

A person with the skills and knowledge related to the construction and operation of the electrical equipment and installations, who has received safety training to identify and avoid the hazards involved.

Request a free quote

Takes about 60 seconds. No obligation.

By submitting, you agree to our Terms of use.

This site is a quote-request service. We connect Texas businesses with a partner firm of licensed Professional Engineers (PE). We are not a licensed engineering firm, do not perform engineering work, sign or seal studies, or provide engineering advice. All engineering is contracted directly with the licensed firm.